Build sideboard

Möbelbau-Anleitung Sideboard

Material
4 x cover caps, white
70 x JD Plus Universal screws (4,0 x 40 mm)
6 x roller thrust guide, 500 mm
Express wood glue
1 x edge band (650 x 45 x 0.4 mm)
375 ml paint
3 x MDF raw (690 x 525 x 3 mm), shelves drawers
12 x connecting fittings R / D
110 x JD Plus Universal screws (3.5 x 25 mm)
mounting glue

1. Arbeitsschritt
1st step
First, attach the plinth panels on the bottom plate corpus. At the back of the plinth panels are mounted flush, the front of the base returns to 2 cm. Screwing takes place from above through the base plate with 3 Universal screws (4,0 x 40 mm). Put The outer holes 10 cm inwards, the third hole set centrally between. Do not forget to always be pre-drilled and to reduce. Now place the two side pieces flush with the rear edge of the bottom plate. Bring each connecting fittings 3 lt. Packing Instructions on to connect the finished floor to the side parts. Connect the base plate fixed to the two sides, while paying attention to the squareness.

2. Arbeitsschritt
2. step
Then insert the cover plate is flush with the rear and side edge. Also bring here each connecting fittings 3 lt. Packing Instructions on to connect the top plate to the side parts. Measure from the top edge to a lateral distance of 5 cm. The third hole is drilled in the center between them. Now you can use the rear panel with 22 Universal screws (4,0 x 40 mm) screw from the back with the body. Put the screws circumferentially uniform.

3. Arbeitsschritt
3. step
The slide rails set flush against the rear wall and the side parts of the body. The distance between the slide rails to the cover plate A is 4.5 cm. Ensure that the sides of the slide rails protrude as a bearing surface 2 cm into the body. Fix the slide rails with 2 universal screws (4,0 x 40 mm) with a lateral distance of 5 cm. Set the short thrust sides mutually aligned between the long sides of the thrust secret compartment. Gluing the contacting surfaces of the thrust side and screw the individual parts, each with 1 Universal screws (4,0 x 40 mm). Then insert the caps on the screw heads. Now you can attach the bottom plate of the secret compartment from below with the resulting frame with 14 Universal screws (3.5 x 25 mm).

4. Arbeitsschritt
4. step
The three drawers are mounted according to the same system as above. For the top drawer you put the short side thrust on all sides between the long flush push pages. Gluing the contacting surfaces of the thrust side and screw the items with 2 universal screws (4,0 x 40 mm). You can then attach (25 mm x 3.5), the bottom plate from below through the floor in the resulting frame with 14 Universal screws. The assembly of the middle and lower drawer is also carried out according to this principle. To do this, two short sides push all sides flush between two long sides of thrust. Gluing the contacting surfaces of the thrust side and screw each the items of the push pages with 2 universal screws (4,0 x 40 mm). Then attach the floor panels of the drawers from the bottom through the floors in the resulting frame with 14 Universal screws (3.5 x 25 mm).

5. Arbeitsschritt
5. step
For a subdivision of the middle drawer make the two middle parts as desired upright in the drawer. Screw both parts of the front and rear with 2 x Universal screws (4,0 x 40 mm).

6. Arbeitsschritt
6. step
Now you can attach the Drawer runners on the carcass and the drawers. Proceed as follows: For the guides on the side panels you always measure from the top edge of the base plate body to the lower edge of the rolling shear guide each 2 cm, 26 cm and 50 cm from. Screw the thrust roller guide with 3 Universal screws (3.5 x 25 mm).

7. Arbeitsschritt
7. step
The counterparts of the rolling shear leadership you bring to flush with the rear and bottom of the finished drawers. Fasten these with 3 Universal screws (3.5 x 25 mm) on the drawer. Then push all the drawers and the secret compartment in the body.

8. Arbeitsschritt
8. Working Step
To assemble the drawer fronts set the finished body incl. Drawers on the back of the rear wall. Label the fronts of the drawers (except secret compartment) with mounting glue and insert the drawer fronts on the drawers on. Align the distances with the aid of plastic wedges like that encircling a uniform distance arises. Also remember the spaces between the drawer fronts. Please refer to the drying time of the adhesive assembly.

9. Arbeitsschritt
9. step
After drying, you can set up the sideboard again and remove the wedges. Then attach the drawer fronts from the inside in addition with 6 Universal screws (3.5 x 25 mm). The finger holes are drilled with 25 mm Forstner bit from the outside, eg. As the center of the drawer fronts, drawer fronts and through the front of the drawer sides. Do not forget, then to paint the inside of the finger holes. Finished!


0 comments:

Post a Comment